Avaya IP Ofice 8.0 Quick Mode Instaltion Download | Manualshive

Page: 167 / 256

background image

IP Office Basic Edition - Quick Mode Installation

Page 167

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

System Components: IP500 Base Cards

9.3 IP500 Trunk Daughter Cards

Most

IP500 base cards

can be fitted with an IP500 trunk daughter

cards to support the connection of trunks to the base card.

Each daughter card is supplied with the stand off pillars required for
installation and a label to identify the daughter cards presence on the
front of the base card after installation.

·

IP500 Combination cards are pre-fitted with a trunk daughter card
which cannot be removed or changed for another type of trunk
daughter card.

IP500 Analog Trunk Daughter Card

This card allows the base card to support 4 analog loop-start trunks.

·

The analog phone ports do not include a ringing capacitor.
Where this is a requirement, connection should be via a Master
socket containing ringing capacitors.

·

If fitted with an IP500 Analog Trunk daughter card, during
power failure phone port 8 is connected to analog trunk port
12.

·

Maximum: 4 per control unit.

IP500 PRI-U Trunk Daughter Card

This card allows the base card to support up to 2 PRI trunk
connections. The card is available in single and dual port variants.
The card can be configured for E1 PRI, T1 robbed bit, T1 PRI or E1R2
PRI trunks.

·

Maximum: 1 single port card per control unit.

·

The IP Office system supports 8 unlicensed B-channels on each
IP500 PRI-U port fitted. Additional B-channels, up to the capacity
of ports installed and PRI mode selected require

IP500 Universal

PRI (Additional Channels)

licenses added to the

configuration. These additional channels consume the licenses
based on which additional channels are configured as in-service
from port 9 of slot 1 upwards. D-channels are not affected by
licensing.

IP500 BRI Trunk Daughter Card

This card allows the base card to support up to 4 BRI trunk
connections, each trunk providing 2B+D digital channels. The card is
available in 2 port (4 channels) and 4 port (8 channels) variants.

·

Maximum: 4 per control unit.

·

IP Office Basic Edition - Quick Mode mode systems are limited
to a maximum of 12 BRI channels.

17

168

170

236

169

«
...
165
166
167
168
169
...
»

Summary of Contents for IP Ofice 8.0

































































































































































































































































Reviews:

No comments

Related manuals for IP Ofice 8.0

Brand: Sagem Pages: 97

Brand: Sagem Pages: 99

Brand: Sagem Pages: 99

Brand: Sagem Pages: 89

Brand: Dash Pages: 24

Brand: Alcatel Pages: 36

Brand: Sagem Pages: 115

Brand: Telstra Pages: 101

Brand: Samsung Pages: 144

Brand: Samsung Pages: 160

Brand: Samsung Pages: 162

Brand: Samsung Pages: 186

Brand: Samsung Pages: 144

Brand: Samsung Pages: 195

Brand: Samsung Pages: 195

Brand: Samsung Pages: 7

Brand: Lava Pages: 39

Brand: Splicecom Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands