Avaya IP Ofice 8.0 Quick Mode Instaltion Download

Page: 157 / 256

IP Office Basic Edition - Quick Mode Installation

Page 157

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

System Components: IP500 V2 Control Unit

Ports

Description

AUDIO

3.5mm Stereo jack socket. Used for external music on hold source input.

AUX

If pressed during a restart of the control unit, the control unit

skip booting

from the /primary folder

on the System SD card. If pressed for more than 5 seconds when a system is running, the control unit
will

shutdown

for 10 minutes.

CPU

Indicates the status of the control unit.

Alternate red/green = Starting up.

Green on = Okay.

Red on = No software.

Flashing Red = Error/Shutdown.

EXPANSION

RJ45 socket. Used for direct connection to external expansion modules using the Expansion Interconnect
cable supplied with the expansion module.

EXT O/P

3.5mm Stereo jack socket. Used for switching external relay systems such as door entry controls. The
port contains two independent switches controlled by the IP Office.

INPUT

AC power input port.

LAN

RJ45 socket. The port is a full-duplex 10/100Mbps auto-sensing, MDI crossover port.

Optional SD

Used for the Optional SD card. The LED is used in the same way as for the System SD (see below).

RESET

This switch is used to restart the IP Office, optionally erasing the configuration and or the core software in
the process. See

Reset Button

RS232

9-Way D-Type socket. Used for system maintenance.

System SD

Used for the System SD card,. The LED is used as follows.

Off =

Card shutdown

Green on = Card present.

Green flashing = Card in use.

Orange steady = Reset imminent.

Red flashing = Card initializing or shutting down.

Red fast flashing = card full

Red steady = Card failure/wrong type.

WAN

RJ45 socket. This port is not supported on systems running in IP Office Basic Edition - Quick Mode mode.

Used for connection of a

functional or protective ground

. Use of a ground for all systems is

recommended and for some locales may be a regulatory requirement.

222

137

110

227

124

228

134

125

126

134

150

228

Summary of Contents for IP Ofice 8.0

































































































































































































































































Search results

Summary of Contents for IP Ofice 8.0

Reviews:

Related manuals for IP Ofice 8.0

Brands by name

Popular brands

Avaya IP Ofice 8.0, Quick Mode Instaltion

Search results

Summary of Contents for IP Ofice 8.0

Reviews:

Related manuals for IP Ofice 8.0

Brands by name

Popular brands