Avaya IP Ofice 8.0 Quick Mode Instaltion Download Page 62 | Manualshive

Page: 62 / 256

background image

IP Office Basic Edition - Quick Mode Installation

Page 62

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

4.4 IP500 Card Installation

The IP500 base cards and trunk daughter cards should be fitted before power
is applied to the control unit. Ensure that cards are inserted in the order that
matches the planned or pre-built configuration.

1.

Fitting IP500 Trunk Daughter Cards to the Base Cards.

2.

Installing IP500 Cards into the Control Unit.

·

Warnings

·

Correct anti-static protection steps should be taken before handling circuit boards.

·

Cards must never be added or removed from the control unit while it has power connected.

·

General Notes

·

Cards can be fitted in any order into any available slots.

·

For phone based administration, the card in slot 1 must be able to support ETR 18D, ETR 34D, M7324, M7310,
T7316E, T7316, 1408 or 1416 phones.

·

It is recommended that cards are fitted from left to right.

·

There are restrictions to the number of supported cards of some types. When such a limit is exceed, the right-
most card of that type will not function.

·

Ensure that you use the labels supplied to identify the card fitted into the control unit.

63

65

«
...
60
61
62
63
64
...
»

Summary of Contents for IP Ofice 8.0

































































































































































































































































Reviews:

No comments

Related manuals for IP Ofice 8.0

Brand: TANDBERG Pages: 3

Brand: Camrivox Pages: 4

Brand: Acer Pages: 56

Brand: Alcatel Pages: 24

Brand: QUO Pages: 5

Brand: Yezz Pages: 5

Brand: Watchguard Pages: 12

Brand: Yezz Pages: 23

JOURNEY IS-Q3100

Brand: iSwag Pages: 42

Brand: Ericsson Pages: 56

Ecom Smart-Ex 02

Brand: Pepperl+Fuchs Pages: 60

Brand: Allworx Pages: 6

Brand: TCL Pages: 33

Brand: Alcatel Pages: 28

Brand: Xorcom Pages: 2

Brand: Zte Pages: 156

Brand: Yealink Pages: 118

Brand: Lemon Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands