Avaya IP Ofice 8.0 Quick Mode Instaltion Download Page 34 | Manualshive

Page: 34 / 256

background image

IP Office Basic Edition - Quick Mode Installation

Page 34

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

1.9 SIP Trunks

The IP Office Basic Edition - Quick Mode mode can support SIP trunks through its LAN connection. These are configured
using IP Office Manager, they cannot be managed through phone based administration.

In order to support SIP trunks, the system must include the following resources:

·

SIP Trunk Licenses
These licenses are used to configure the number of simultaneous SIP trunk calls supported, up to a maximum of
20. A IP Office Basic Edition - Quick Mode mode system supports 3 channels without licenses.

·

Voice Compression Channels
These are required to convert between the audio compression methods used for IP telephony and those used for
analog and digital trunks. Each IP500 Combination card, up to a maximum of 2 cards, installed in the system
provides 10 voice compression channels for the system. One voice compression channel is used for each SIP call.

«
...
32
33
34
35
36
...
»

Summary of Contents for IP Ofice 8.0

































































































































































































































































Reviews:

No comments

Related manuals for IP Ofice 8.0

OfficeServ WIP-5000M

Brand: Samsung Pages: 108

OfficeServ ITP-5107S

Brand: Samsung Pages: 40

StarLink SLE-LTE Commercial Series

Brand: NAPCO Pages: 20

Brand: Majestic Pages: 57

Brand: TECNO MOBILE LIMITED Pages: 6

Vogue 2.8a SLEEC

Brand: iBall Pages: 23

Brand: Azumi Pages: 28

Brand: Wynncom Pages: 27

Brand: Grandstream Networks Pages: 12

Brand: Sony Ericsson Pages: 26

Brand: Crestron Pages: 422

Brand: Zte Pages: 58

Brand: Xiaomi Pages: 103

Brand: Zte Pages: 89

Brand: i-mobile Pages: 39

Brand: Sigma Pages: 16

Brand: Samsung Pages: 184

Brand: Zte Pages: 167

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands