Avaya IP Ofice 8.0 Quick Mode Instaltion Download Page 69 | Manualshive

Page: 69 / 256

background image

IP Office Basic Edition - Quick Mode Installation

Page 69

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

IP500 V2 Installation: Wall Mounting

4.5.2 Wall Mounting Kit V1

These notes relate to the older design of wall mounting kit (SAP 70043015) used
for IP500 and IP500v2 control units. This kit cannot be used for external expansion
modules.

The kit includes two brackets, one top and one bottom, and screws for attachment
to the control unit. Additional 4 x 4.5mm fixtures and fittings are required suitable
for the wall type.

In addition to the existing

environmental requirements

for an IP Office system,

the following additional requirements apply when wall mounting a unit:

·

The wall surface must be vertical, flat and vibration free. Attachment to
temporary walls is not supported.

·

Only the screws provided with the mounting kit should used to attach the
brackets to the control unit.

·

The brackets must be used as shown, with the deeper tray-like bracket used
at the bottom of the wall mounted control unit.

40

«
...
67
68
69
70
71
...
»

Summary of Contents for IP Ofice 8.0

































































































































































































































































Reviews:

No comments

Related manuals for IP Ofice 8.0

Factor SPH-M260

Brand: Samsung Pages: 118

Brand: Samsung Pages: 2

Brand: Samsung Pages: 34

Brand: Yealink Pages: 38

Brand: Samsung Pages: 135

Brand: AU Pages: 3

Brand: UMX Pages: 12

Brand: Wileyfox Pages: 58

Brand: Smartbox Pages: 84

IP Pathfinder S

Brand: Fujitsu Pages: 28

IP Centrex SRS-12i

Brand: Fujitsu Pages: 69

Brand: Blackberry Pages: 126

Carephone 62 CRS-H62M-GB

Brand: Bosch Pages: 72

Brand: Bosch Pages: 52

Brand: Toshiba Pages: 126

Brand: TCT Mobile Pages: 65

Brand: TCL Pages: 97

Brand: Storex Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands