manualshive.com logo in svg

AMD Elan SC520, User Manual, Page: 358 / 444

Share
Download
AMD Elan SC520 User Manual Download Page 358

UART Serial Ports

21-12

Élan™SC520 Microcontroller User’s Manual

21.5.7.1

Serial Port Interrupts

Each serial port supports the standard UART interrupts. These include: 

■

Received data available or FIFO trigger level reached

■

Transmit Holding register empty (THRE)

■

Modem status change (including clear-to-send, data-set-ready, ring indicator, data 
carrier detect)

■

Line Status register receiver interrupts (including overrun error, parity error, framing error 
and break interrupt)

In 16550-compatible mode, the FIFO time-out interrupt is also enabled when the received 
data available interrupt is enabled. 

The UART interrupt sources and their priority are shown in Table 21-7. If two interrupt 
sources are pending simultaneously, the highest priority interrupt is indicated by the ID field 
of the UART x Interrupt ID (UARTxINTID) register. When the interrupt source is cleared, a 
subsequent read from this port returns the next highest priority interrupt source. 

Note: In 16450-compatible mode, the INT_ID2 bit always reads back 0. The INT_ID bit 
field is located in the UART x Interrupt ID (UARTxINTID) register.

The UART interrupts are enabled by the Interrupt Enable register and read from the UART 
x Interrupt ID (UARTxINTID) register.

21.5.7.2

DMA Interrupts

Each UART can generate an interrupt when the Transfer Count (TC) signal associated with 
DMA transfers is asserted. Four enable bits and four status bits are available for these 
interrupts: transmit and receive Transfer Count reached for each UART. These bits are 
located in the UART x General Control (UARTxCTL) and UART x General Status 
(UARTxSTA) registers.

Table 21-7

Serial Port Interrupt and Interrupt Priority

INT_ID

Bit Field

Description

Identification Priority

000b

Modem status change

Fourth (Lowest)

001b

Transmit holding register empty (16540-compatible 
mode)/Transmit FIFO empty (16550-compatible mode)

Third

010b

Received data available (16540-compatible mode)/
Receiver FIFO trigger (16550-compatible mode)

Second

011b

Receive line status

First (Highest)

100b

Not used

—

101b

Not used

—

110b

FIFO time-out

Second

111b

Not used

—

Summary of Contents for Elan SC520





























































































































































































































































































































































































































































Reviews:

No comments