manualshive.com logo in svg

AMD Elan SC520, User Manual, Page: 302 / 444

Share
Download
AMD Elan SC520 User Manual Download Page 302

Programmable Interrupt Controller

15-14

Élan™SC520 Microcontroller User’s Manual

Since programmable inversion of the interrupt signal is available, the external device can 
generate an interrupt to the ÉlanSC520 microcontroller by either driving the interrupt 
request line Low and allowing a pullup resistor to generate the rising edge or by actively 
driving the line Low from its default High inactive state through a pullup resistor (as in PCI 
interrupt generation). 

Sharing edge-triggered interrupts in the ÉlanSC520 microcontroller is not recommended. 

For more information about this topic, see “Software Considerations” on page 15-18.

15.5.6

Non-Maskable Interrupts and Routing

A unique feature of the ÉlanSC520 microcontroller’s PIC is its ability to route most of its 
hardware interrupt sources via software to generate a non-maskable interrupt (NMI) to the 
CPU. 

■

With the exception of the internally-generated ECC interrupt from the SDRAM controller, 
all the other interrupt sources can be routed to the Am5

x

86 CPU’s NMI input. 

■

The PCI host bridge and SDRAM controller each generate a separate and distinct NMI 
interrupt source to the PIC. The interrupt source can only generate an NMI and not a 
maskable interrupt to the CPU. 

There are 34 interrupt sources for NMI generation to the CPU: 

■

15 external interrupts

■

18 internally-generated interrupts

■

1 software NMI source

Figure 15-4 on page 15-15 shows the logical implementation of NMI generation in the 
ÉlanSC520 microcontroller.

15.5.6.1

Sharing NMIs

NMIs can be shared in the ÉlanSC520 microcontroller. NMI sources are routed logically to 
an OR gate, as shown in Figure 15-4 on page 15-15. 

Each individual interrupt source is gated by an enable signal to selectively allow it to be 
shared with the other interrupt sources. Each of these enable signals is controlled via the 
Interrupt Mapping (xMAP) registers and is enabled by programming its interrupt routing bits 
to 11111b. An NMI Enable (NMI_ENB) bit in the Interrupt Control (PICICR) register (MMCR 
offset D00h) provides the mechanism to prevent all NMIs from reaching the CPU. This bit 
has been moved from the PC/AT-compatible location (see “Legacy NMI Enable Bit Moved” 
on page 20-10 for more details). NMIs are disabled on system and soft reset and must be 
enabled via setting the NMI_ENB bit before use.

It is recommended that sharing NMIs be done using level-sensitive NMIs only. All NMIs 
should be treated similarly to the maskable interrupt sources. All NMIs once asserted should 
remain asserted until cleared by software. The NMI_DONE bit located in the Interrupt 
Control (PICICR) register facilitates NMI sharing. This bit is visible to all NMI handlers, and 
the currently executing NMI handler should clear the NMI source prior to asserting the 
NMI_DONE bit. NMI handler software should write a 1 to the self-clearing NMI_DONE bit 
immediately before executing the IRET instruction to exit from the handler. Setting the 
NMI_DONE bit deasserts the NMI signal to the CPU for a brief time before allowing any 
other pending NMI requests to be serviced, in order to satisfy NMI timing requirements of 
the CPU. 

Sharing edge-triggered NMIs in the ÉlanSC520 microcontroller is not recommended. 

Summary of Contents for Elan SC520





























































































































































































































































































































































































































































Reviews:

No comments