manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

7

General Maintenance

To Clean the EI HES

5977B Series MSD Operating Manual

185

These are the parts that contact the sample or ion beam. The other parts 
normally should not require cleaning.

3

If the contamination is serious, such as an oil backflow into the analyzer, 
seriously consider replacing the contaminated parts

CAUTION

If insulators are dirty, clean them with a cotton swab dampened with 
reagent-grade methanol. If that does not clean the insulators, replace them. Do 
not abrasively or ultrasonically clean the insulators.

Figure 58   EI HES parts to be cleaned

Source body

Repeller

Entrance 
lens (1)

Ion focus 
lens (2)

Post extractor 
lens 2 (3) 

Post extractor 
lens 1 (4)

Extractor 
lens (5)

CAUTION

The filaments, source heater assembly, insulators, source mounting plate, and 
filament block cannot be cleaned ultrasonically. Replace these components if 
major contamination occurs.

CAUTION

Do not use the abrasive slurry on the source mount bushings.

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Oerlikon Barmag GF Assembly Instructions Manual preview
GF
Brand: Oerlikon Barmag Pages: 36
Gardena 2000/2 Li-18 Operator'S Manual preview
2000/2 Li-18
Brand: Gardena Pages: 17
Gardena 4100 Silent Operator'S Manual preview
4100 Silent
Brand: Gardena Pages: 12
Xylem e-MPA Instruction Manual preview
e-MPA
Brand: Xylem Pages: 44
Kamoer ATO One for RO Quick Start Manual preview
ATO One for RO
Brand: Kamoer Pages: 2
Wijas PERFECT 350 ELECTRONIC Assembly And Operation Manual preview
PERFECT 350 ELECTRONIC
Brand: Wijas Pages: 9
Kayoba 650-459 Operating Instructions Manual preview
650-459
Brand: Kayoba Pages: 6
Warren rupp NG2SS Service & Operating Manual preview
NG2SS
Brand: Warren rupp Pages: 13
WaterGroup E75TFC-3 Installation, Operation And Service Manual preview
E75TFC-3
Brand: WaterGroup Pages: 24
CareFusion Alaris CC Guardrails 80033UND1-G Directions For Use Manual preview
Alaris CC Guardrails 80033UND1-G
Brand: CareFusion Pages: 40
CME T34L Operator'S Manual preview
T34L
Brand: CME Pages: 28
IDEAL Solar Thermal Installation And Servicing preview
Solar Thermal
Brand: IDEAL Pages: 68
FLORABEST 85992 Translation Of Original Operation Manual preview
85992
Brand: FLORABEST Pages: 48
KC 23.580 Manual preview
23.580
Brand: KC Pages: 11
COSMOGAS GB 06 Manual preview
GB 06
Brand: COSMOGAS Pages: 182
Graco Husky 307 F Series Instructions-Parts List Manual preview
Husky 307 F Series
Brand: Graco Pages: 36
Danfoss DHP-H Varius Pro+ Manual preview
DHP-H Varius Pro+
Brand: Danfoss Pages: 36
Daikin VRVIII Operation Manual preview
VRVIII
Brand: Daikin Pages: 24

Brands by name

Popular brands

Load more brands