Agilent Technologies 5977B CI MSD Operating Manual Download Page 181 | Manualshive

Page: 181 / 254

background image

7

General Maintenance



To Disassemble the EI HES

5977B Series MSD Operating Manual

181

To Disassemble the EI HES

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Cloths, clean (05980-60051)

•

T6 Torx driver, (8710-2548)

•

Tweezers (8710-2460)

Procedure

Refer to the exploded parts view

and the EI HES parts list

page 182 while using this procedure.

1

Place a clean cloth on your work surface to hold the ion source parts.

2

Use a T6 Torx screwdriver to remove the screw securing the filament block
to the source mount. Use the finger grip to remove the filament block.

3

Remove the dual filament from the filament block by lifting the source body
up off of the filament block, while holding the filament block so that the dual
filament will not fall and become damaged.

4

Use a T6 Torx screwdriver to remove the two screws securing the source
mount to the source body.

5

Remove the source mount from the lens body.

6

Remove the repeller and ring heater sensor assembly from the source body.

7

Separate the repeller from the ring heater assembly.

8

Use a T6 Torx screwdriver to remove the screw and locking ring for the lens insulator
that secures the lens stack in the source body, then remove the lens stack.

CAUTION

Use care when removing the filament from the filament block. Excessive stress
can crack the filament ceramic. If this happens, do not attempt to operate with
a defective filament, it must be replaced.

CAUTION

Never remove the finger grip from the filament block.

«
...
179
180
181
182
183
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: Bacharach Pages: 12

LEH150-E Series

Brand: Liberty Pumps Pages: 83

Brand: EINHELL Pages: 44

Feeder/Deliming System EV9797-20

Brand: Everpure Pages: 2

TURBO-FLUX modular

Brand: Cattani Pages: 61

POWERplus POWX1700

Brand: VARO Pages: 10

Brand: Leader Pumps Pages: 8

Brand: Ocean Technologies Pages: 2

FXV-1212C-32Q-M/Q

Brand: BAC Pages: 47

Brand: A.O. Smith Pages: 4

Brand: Battery Watering Technologies Pages: 2

Comfort 5000/5 LCD

Brand: Gardena Pages: 13

Brand: Binks Pages: 22

Masterflex L/S 7569-00

Brand: Cole Parmer Pages: 8

Brand: Graco Pages: 46

Brand: Rheem Pages: 50

Brand: A.O. Smith Pages: 28

Brand: Quooker Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands