Agilent Technologies 5977B CI MSD Operating Manual Download Page 122 | Manualshive

Page: 122 / 254

background image

5

Operating in EI Mode



To Set Analyzer Temperatures from the Instrument Control View

122

5977B Series MSD Operating Manual

To Set Analyzer Temperatures from the
Instrument Control View

MSD ion source and Quad temperatures are stored in the current tune (*.u) file.
When a method is loaded, the setpoints in the tune file associated with that
method are downloaded automatically.

Procedure

1

In

Instrument Control

view, select

MS Temperatures

from the

Instrument

menu. (See

.)

2

Enter the

MS Source

and

MS Quad

(mass filter) temperatures in the

Setpoint

and

Limit

fields. (See

.)

The GC/MSD interface, ion source, and quadrupole heated zones interact.
The analyzer heaters may not be able to accurately control temperatures if
the setpoint for one zone is much different from that of an adjacent zone.

Figure 37 MS temperatures dialog

Table 9

Recommended temperature settings

EI operation

PCI operation

NCI operation

MS Source

230

250

150

MS Quad

150

150

150

CAUTION

Do not exceed 200 °C for the quadrupole or 350 °C for the source.

«
...
120
121
122
123
124
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: YANGTECH Pages: 16

Brand: Quooker Pages: 12

DURA-Power DRE-52

Brand: A.O. Smith Pages: 26

DURA-Power DRE-52

Brand: A.O. Smith Pages: 20

THBF701 Master Series

Brand: bluefin Pages: 17

Brand: Newton Pages: 4

Brand: UDOR Pages: 96

Brand: GORMAN-RUPP PUMPS Pages: 52

Brand: Navien Pages: 60

Wilden Advanced P400

Brand: Dover Pages: 56

Brand: Textron Pages: 20

Brand: Carrier Pages: 28

Shoebox Heat Pump

Brand: Kensa Heat Pumps Pages: 20

AquaMax Eco Premium 4000

Brand: Oase Pages: 121

Brand: P.I.T. Pages: 18

Brand: salmson Pages: 25

Brand: Graco Pages: 16

Brand: Aquacal Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands