manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

8

CI  Maintenance

To Clean the CI Source

5977B Series MSD Operating Manual

243

5

Ultrasonically clean the parts (each group separately) for 15 minutes. For 
dirty parts, use all three solvents in the order shown, cleaning 15 minutes with 
each of the following solvents:

•

Methylene chloride (reagent-grade)

•

Acetone (reagent-grade)

•

Methanol (reagent-grade)

For routine cleaning, cleaning with methanol is sufficient.

6

Place the parts in a clean beaker. 

Loosely

 cover the beaker with clean 

aluminum foil (dull side down).

7

Dry the cleaned parts in an oven at 100 °C for five to six minutes.

WARNING

Al

All of these solvents are hazardous. Work in a fume hood and take all 
appropriate precautions.

WARNING

Let 

Let the parts cool before you handle them.

NOTE

Take care to avoid contaminating cleaned and dried parts. Put on new, clean 
gloves before handling the parts. Do not set the cleaned parts on a dirty 
surface. Set them only on clean, lint-free cloths.

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Vaillant aroSTOR VWL B 200/5 UK Operating Instructions Manual preview
aroSTOR VWL B 200/5 UK
Brand: Vaillant Pages: 24
Vaillant ecoFIT pure Operating Instructions Manual preview
ecoFIT pure
Brand: Vaillant Pages: 20
Vaillant VIH R 300/3 BR Manual preview
VIH R 300/3 BR
Brand: Vaillant Pages: 24
Watson-Marlow 530 Du Operating Manual preview
530 Du
Brand: Watson-Marlow Pages: 128
York E4TS030 Owner'S Manual preview
E4TS030
Brand: York Pages: 4
Grundfos Sololift+ WC-1 Installation And Operating Instructions Manual preview
Sololift+ WC-1
Brand: Grundfos Pages: 16
Texmo Industries Taro HCS SJ Series Instructions & Operating Manual preview
Taro HCS SJ Series
Brand: Texmo Industries Pages: 41
DAYLIFF DDW 750V Installation & Operating Manual preview
DDW 750V
Brand: DAYLIFF Pages: 8
Malmbergs SVQ250F Instruction Manual preview
SVQ250F
Brand: Malmbergs Pages: 12
Alpine VORTEX PEG1800 Owner'S Manual preview
VORTEX PEG1800
Brand: Alpine Pages: 20
Calorex IPT 8 Series Owners & Installation Manual preview
IPT 8 Series
Brand: Calorex Pages: 44
Mallory 4060FI Installation Instructions preview
4060FI
Brand: Mallory Pages: 4
KBS mini-Compacta Installation & Operating Manual preview
mini-Compacta
Brand: KBS Pages: 86
ubbink PoolFilter Manual preview
PoolFilter
Brand: ubbink Pages: 40
Geotech Geopump I Series Installation And Operation Manual preview
Geopump I Series
Brand: Geotech Pages: 16
Q-MAX ULTRA-FLO MY3-50 METAL Series Assembly, Installation And Operation Manual preview
ULTRA-FLO MY3-50 METAL Series
Brand: Q-MAX Pages: 12
Clarke 7230582 Operation & Maintenance Instructions Manual preview
7230582
Brand: Clarke Pages: 12
Graco Husky 307 F Series Instructions-Parts List Manual preview
Husky 307 F Series
Brand: Graco Pages: 36

Brands by name

Popular brands

Load more brands