Agilent Technologies 5977B CI MSD Operating Manual Download Page 28

Page: 28 / 254

Introduction



Safety and Regulatory Certifications

5977B Series MSD Operating Manual

Safety and Regulatory Certifications

The 5977B Series MSD conforms to the following safety standards:

•

Canadian Standards Association (CSA): CAN/CSA-C222 No. 61010-1-04

•

CSA/Nationally Recognized Test Laboratory (NRTL): UL 61010–1

•

International Electrotechnical Commission (IEC): 61010–1

•

EuroNorm (EN): 61010–1

The 5977B Series MSD conforms to the following regulations on
Electromagnetic Compatibility (EMC) and Radio Frequency Interference (RFI):

•

CISPR 11/EN 55011: Group 1, Class A

•

IEC/EN 61326

•

AUS/NZ

This ISM device complies with Canadian ICES-001. Cet appareil ISM est
conforme a la norme NMB—001 du Canada.

EMC declaration for South Korea

This equipment has been evaluated for its suitability for use in a commercial
environment. When used in a domestic environment, there is a risk of radio
interference.

The 5977B Series MSD is designed and manufactured under a quality system
registered to ISO 9001.

The 5977B Series MSD is RoHS compliant.

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands