Agilent Technologies 5977B CI MSD Operating Manual Download Page 225

Page: 225 / 254

CI Maintenance



To Connect/Disconnect Wiring to the EI HES Radiator

5977B Series MSD Operating Manual

225

To Connect/Disconnect Wiring to the EI HES
Radiator

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Pliers, long-nose (8710-1094)

•

Tweezers (8710-2460)

Procedure

Use tweezers or needle nose pliers to connect/disconnect the green ground
wire and the 5 lens wires from the radiator. Do not bend the wires any more
than necessary. (See

Figure 73

Use tweezers or needle nose pliers to connect/disconnect the 2 purple
source heater wires and the 2 gray RTD wires from the ceramic source
board.

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands