Agilent Technologies 5977B CI MSD Operating Manual Download Page 237

Page: 237 / 254

CI Maintenance



To Connect/Disconnect EI HES Model Wiring to the CI Source

5977B Series MSD Operating Manual

237

To Connect/Disconnect EI HES Model Wiring
to the CI Source

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Pliers, long-nose (8710-1094)

•

Tweezers (8710-2460)

Procedure

Use pliers to connect/disconnect the ceramic board wire leads (red, white,
black, and gray) at the source connectors. (See

Figure 77

Use pliers to connect/disconnect the source heater wire leads at the ceramic
source board. (See

Figure 77

Figure 77 Wiring between the ceramic source board and the source

Filament 1

Repeller

Dummy filament

Entrance lens

Ion focus

Source heater

Source RTD

Ceramic source board

Filament 1

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands