manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

5

Operating in EI Mode

To Perform High-Mass Testing

132

5977B Series MSD Operating Manual

To Perform High-Mass Testing

Materials needed

•

PFHT High Mass checkout sample 3 × 1 mL (5188-5357)

Procedure

1

Load the autotune file (atune.u, HES_atune.u, etune.u) then auto tune the 
MSD. (See 

“To Tune the MSD in EI Mode” 

on page 127.)

2

Resolve the PFHT.M method under 

MassHunter\MSD\x\methods\checkout\PFHT.M 

where x is the instrument number being used. 

3

Update and save the method.

4

Load the PFHT calibration sample into a vial and place in position 2.

5

In 

Instrument Control

 view select 

High Mass Check

 from the 

Checkout

 

menu.

6

Follow the instructions on screen.

7

The run is completed, and results are printed within 5 minutes. (See 

Figure 43

 on page 133.)

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Gardena 9200 Operator'S Manual preview
9200
Brand: Gardena Pages: 182
Calpeda CT Series Operating Instructions Manual preview
CT Series
Brand: Calpeda Pages: 16
Eaton 70360 Parts And Repair Information preview
70360
Brand: Eaton Pages: 29
SAB F101 Instructions For Use Manual preview
F101
Brand: SAB Pages: 7
Xylem Bell & Gossett Domestic 616PF Instruction Manual preview
Bell & Gossett Domestic 616PF
Brand: Xylem Pages: 4
CTC Union 588347301 Installation And Maintenance Manual preview
588347301
Brand: CTC Union Pages: 28
salmson SXE-DXE Installation And Starting Instructions preview
SXE-DXE
Brand: salmson Pages: 28
Wilo CronoBloc BL Series Installation And Operating Instructions Manual preview
CronoBloc BL Series
Brand: Wilo Pages: 43
F.F. Group SPP 800X Original Instructions Manual preview
SPP 800X
Brand: F.F. Group Pages: 28
Malmbergs 88 792 56 Instruction Manual preview
88 792 56
Brand: Malmbergs Pages: 12
andrews Maxxflo CWH120/200 Installation, Operation And Maintenance Manual preview
Maxxflo CWH120/200
Brand: andrews Pages: 44
EINHELL GC-AW 1136 Original Operating Instructions preview
GC-AW 1136
Brand: EINHELL Pages: 88
Waterous CPK-5 Series Overhaul Instructions preview
CPK-5 Series
Brand: Waterous Pages: 7
ICP HC4H3 Installation Instructions Manual preview
HC4H3
Brand: ICP Pages: 17
CH GFH(12)EA-D3DNA1A/I Owner'S Manual preview
GFH(12)EA-D3DNA1A/I
Brand: CH Pages: 8
Pressol Pneumatic grease pump 50:1 Operating Instructions Manual preview
Pneumatic grease pump 50:1
Brand: Pressol Pages: 14
Lochinvar Squire SSS03 Installation And Operation Manual preview
Squire SSS03
Brand: Lochinvar Pages: 20
Vortex BW-SL 154 Manual preview
BW-SL 154
Brand: Vortex Pages: 40

Brands by name

Popular brands

Load more brands