Agilent Technologies 5977B CI MSD Operating Manual Download Page 127

Page: 127 / 254

Operating in EI Mode



To Tune the MSD in EI Mode

5977B Series MSD Operating Manual

127

To Tune the MSD in EI Mode

You can also use the 7890B GC control panel to run the autotune that is currently
loaded in MassHunter. (See

“Operating the MSD from the 7890 GC Control

Panel”

on page 104.)

Procedure

Load the method that will be used for data acquisition.

In the

Instrument Control

view, verify the correct tune file is displayed in the

tile bar. For most applications,

Autotune

gives good results.

To select a different tune file select

MS Tune File

from the

Instrument

to display the

Select Tune File

dialog. The

Settings

area displays the

important parameters for a selected tune file.

The tune file must match the type of ion source in the analyzer. If you are
using an EI source, select a tune file created for an EI source.

Click the

Tune

icon

to display the

Select Tune Type

dialog. (See

Figure 40

Select

Tune MSD

to perform a complete autotune, or select

Quick Tune

adjust peak width, mass assignment, and abundance, without changing ion
ratios.

Click

to close this dialog and start the tune. If the MSD temperatures are

not stable, you are prompted to wait or override the wait by clicking

Override

Figure 40 Select tune type dialog

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands