Agilent Technologies 5977B CI MSD Operating Manual Download Page 163

Page: 163 / 254

Operating in CI Mode



To Verify PCI Performance

5977B Series MSD Operating Manual

163

To Verify PCI Performance

Materials needed

•

Benzophenone, 100 pg/



L 5 × 1 mL (8500-5440)

Procedure

Verify that the MSD performs correctly in EI mode.

Verify that the

PCICH4.U

tune file is loaded.

Select

Gas A

and set flow to 20%.

Tune and Vacuum Control

view, perform CI setup. (See

“To Perform a PCI

Autotune (Methane Only)”

on page 159.)

Run CI Autotune. (See

“CI Autotune”

on page 145.)

Run the PCI sensitivity method

BENZ_PCI.M

using 1 µL of 100 pg/µL

benzophenone.

Verify that the system conforms to the published sensitivity specification.
Please refer to the Agilent Web site at

www.agilent.com/chem

for

specifications.

CAUTION

Always verify MSD performance in EI before switching to CI operation. (See

“To Verify EI System Performance”

on page 131.) Always set up the CI MSD in

PCI first, even if you are going to run NCI.

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands