Agilent Technologies 5977B CI MSD Operating Manual Download Page 170 | Manualshive

Page: 170 / 254

background image

7

General Maintenance



Before Starting

170

5977B Series MSD Operating Manual

Dangerous temperatures

Many parts in the MSD operate at, or reach, temperatures high enough to cause
serious burns. These parts include, but are not limited to:

•

GC inlet

•

GC oven and its contents

•

GC detector

•

GC valve box

•

Foreline pump

•

Heated MSD ion source, GC/MSD interface, and quadrupole

The GC inlets and GC oven also operate at very high temperatures. Use the same
caution around these parts. See the documentation supplied with your GC for
more information.

Chemical residue

Only a small portion of your sample is ionized by the ion source. The majority of
any sample passes through the ion source without being ionized. It is pumped
away by the vacuum system. As a result, the exhaust from the foreline pump will
contain traces of the carrier gas and your samples. Exhaust from the standard
foreline pump also contains tiny droplets of foreline pump oil.

An oil trap is supplied with the standard foreline pump. This trap stops

only

pump

oil droplets. It

does not

trap any other chemicals. If you are using toxic solvents

or analyzing toxic chemicals, do not use this oil trap. For all foreline pumps,

WARNING

Never touch these parts while your MSD is on. After the MSD is turned off, give
these parts enough time to cool before handling them.

WARNING

The GC/MSD interface heater is powered by a thermal zone on the GC. The
interface heater can be on, and at a dangerously high temperature, even
though the MSD is off. The GC/MSD interface is well insulated. Even after it is
turned off, it cools very slowly.

WARNING

The foreline pump can cause burns if touched when operating. It has a safety
shield to prevent the user from touching it.

«
...
168
169
170
171
172
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: M&C Pages: 18

Brand: salmson Pages: 12

Brand: SereneLife Pages: 10

Brand: P.I.T. Pages: 20

Brand: Enviroheat Pages: 20

Brand: Enviroheat Pages: 29

Brand: BLACKMER Pages: 12

Brand: Becker Pages: 5

Brand: John Wood Pages: 28

Brand: Danner Pages: 2

Brand: A.O. Smith Pages: 43

Brand: Durapac Pages: 11

Brand: KNF Pages: 88

Brand: Bryant Pages: 54

RIBILAND PRPVC1501V

Brand: Ribimex Pages: 35

Krystal Clear SF90220T

Brand: Intex Pages: 112

Brand: Cosmo Pages: 48

Brand: Elite Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands