Agilent Technologies 5977B CI MSD Operating Manual Download Page 57 | Manualshive

Page: 57 / 254

background image

3

Installing Intuvo 9000 GC Columns



Conditioning columns

5977B Series MSD Operating Manual

57

Conditioning columns

Conditioning a column before it is connected to the GC/MSD interface is
essential.

A small portion of the capillary column stationary phase is often carried away by
the carrier gas. This is called column bleed. Column bleed deposits traces of the
stationary phase in the MSD ion source. This decreases MSD sensitivity and
makes cleaning the ion source necessary.

Column bleed is most common in new or poorly cross-linked columns. It is much
worse if there are traces of oxygen in the carrier gas when the column is heated.
To minimize column bleed, all capillary columns should be conditioned before
they are installed in the GC/MSD interface. (See

“To Condition an Intuvo

Capillary Column”

Tips and hints

•

Always use carrier gas that is at least 99.9995% pure.

•

Always wear clean gloves when handling a component’s click and run
connectors.

•

Always wear clean gloves when handling a gasket.

•

Always wear clean gloves when handling the 9000 GC/MS Tail.

WARNING

If you are using hydrogen as a carrier gas, the hydrogen gas flow must be off
before turning off the MSD power. If the foreline pump is off, hydrogen will
accumulate in the MSD and an explosion may occur. Read

on page 24 before operating the MSD with hydrogen gas.

«
...
55
56
57
58
59
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: valent Pages: 20

Brand: Kamco Pages: 36

Brand: Graco Pages: 48

Brand: Milton Roy Pages: 43

Brand: Oilon Pages: 68

Brand: Sanden Pages: 48

BlackFin CT-2902BPHP

Brand: Panduit Pages: 68

Brand: Yardworks Pages: 19

Brand: Annovi Reverberi Pages: 100

Scalekleen EV9796-01

Brand: Everpure Pages: 2

Brand: IDEAL Pages: 68

Brand: Clarke Pages: 12

Brand: Zodiac Pages: 10

Brand: Pentair Jung Pumpen Pages: 8

Brand: Econ Pages: 37

Brand: Trotec Pages: 18

Brand: Calpeda Pages: 48

Brand: GORMAN-RUPP Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands