manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

8

CI  Maintenance

General Information

222

5977B Series MSD Operating Manual

General Information

Ion source cleaning

The main effect of operating the MSD in CI mode is the need for more frequent 
ion source cleaning. In CI operation, the ion source chamber is subject to more 
rapid contamination than in EI operation because of the higher source pressures 
required for CI.

Ammonia

Ammonia, used as a reagent gas, increases the need for foreline pump 
maintenance. Ammonia causes foreline pump oil to break down more quickly. 
Therefore, the oil in the standard foreline vacuum pump must be checked and 
replaced more frequently.

Always purge the MSD with methane after using ammonia.

Be sure to install the ammonia with the tank in an upright position. This will help 
prevent liquid ammonia from getting into the flow module.

To set up your MSD for CI operation

Setting up your MSD for operation in CI mode requires special care to avoid 
contamination and air leaks.

Guidelines

•

Before venting in EI mode for the installation of the CI source, verify that the 
GC/MSD system is performing correctly. (See

“To Verify EI System 

Performance” 

on page 131.)

•

Make sure the reagent gas inlet line(s) are equipped with gas purifiers (not 
applicable for ammonia).

•

Use extra-high purity reagent gases; 99.99% or better for methane and as 
pure as is available for other reagent gases.

WARNING

Always perform any maintenance procedures using hazardous solvents under 
a fume hood. Be sure to operate the MSD in a well-ventilated room.

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Maag S Series Installation, Operation & Maintenance Manual preview
S Series
Brand: Maag Pages: 16
A.O. Smith 100 Series Installation & Operating Instructions Manual preview
100 Series
Brand: A.O. Smith Pages: 40
Quick B3 Installation And Use Manual preview
B3
Brand: Quick Pages: 16
Ultranatura GP-100 Original Operating Instructions preview
GP-100
Brand: Ultranatura Pages: 24
Vaillant aroTHERM plus Quick Manual preview
aroTHERM plus
Brand: Vaillant Pages: 40
Oasis ELITE AC9 Installation And Instruction Manual preview
ELITE AC9
Brand: Oasis Pages: 44
Kärcher SP 16.000 Dual Original Instructions Manual preview
SP 16.000 Dual
Brand: Kärcher Pages: 16
Mueller Fre-Heater D Series Installation And Operation Manual preview
Fre-Heater D Series
Brand: Mueller Pages: 34
Varian Turbo-V70LP Instruction Manual preview
Turbo-V70LP
Brand: Varian Pages: 44
Debem Boxer 1003 Original Instructions Manual preview
Boxer 1003
Brand: Debem Pages: 68
Barnes 4SE-L series Installation And Operation Manual preview
4SE-L series
Brand: Barnes Pages: 26
Pro-Craft PN17 Manual preview
PN17
Brand: Pro-Craft Pages: 24
Carrier XCT 7 40VC009-048F-7G-QEE Installation And Owner'S Manual preview
XCT 7 40VC009-048F-7G-QEE
Brand: Carrier Pages: 28
salmson SUBSON Premium Installation And Starting Instructions preview
SUBSON Premium
Brand: salmson Pages: 40
Quooker PRO7 Installation Manual preview
PRO7
Brand: Quooker Pages: 20
Dirty Hand Tools 101100 Operation Manual preview
101100
Brand: Dirty Hand Tools Pages: 20
State Water Heaters SUF-130- 300/400/500 Instruction Manual preview
SUF-130- 300/400/500
Brand: State Water Heaters Pages: 76
Viessmann BWT 221.A06 Installation And Service Instructions Manual preview
BWT 221.A06
Brand: Viessmann Pages: 124

Brands by name

Popular brands

Load more brands