Agilent Technologies 5977B CI MSD Operating Manual Download Page 173

Page: 173 / 254

General Maintenance



Maintaining the Vacuum System

5977B Series MSD Operating Manual

173

Maintaining the Vacuum System

Periodic maintenance

Some maintenance tasks for the vacuum system must be performed
periodically. (See

Table 17

on page 168.) These include:

•

Checking the foreline pump fluid (every week)

•

Replacing the tip seal on the optional IDP-3 dry scroll pump (annually)

•

Checking for leaks (every month)

•

Checking the calibration vial(s) (every 6 months)

•

Replacing the foreline pump oil (every 6 months; every 3 months for CI MSDs
using ammonia reagent gas)

•

Tightening the foreline pump oil box screws (first oil change after installation)

•

Replacing the diffusion pump fluid (once a year)

•

Replacing the dry foreline pump seals (once a year)

Failure to perform these tasks as scheduled can result in decreased instrument
performance. It can also result in damage to your instrument.

Other procedures

Tasks such as replacing a foreline vacuum gauge or Micro-Ion vacuum gauge
should be performed only when needed. Refer to the

Agilent 5977B Series MSD

Troubleshooting and Maintenance

manual and the online help in Agilent

MassHunter GC/MS Acquisition software for symptoms that indicate this type of
maintenance is required.

More information is available

If you need more information about the locations or functions of vacuum system
components, refer to the

Agilent 5977B Series MSD Troubleshooting and

Maintenance

manual.

Most of the procedures in this chapter are illustrated with video clips on the
Agilent GC and GC/MS User Manuals and Tools DVD set and the Agilent GC/MS
Software Information and Manuals memory stick.

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands