Agilent Technologies 5977B CI MSD Operating Manual Download Page 246

Page: 246 / 254

CI Maintenance



To Assemble the CI Source

246

5977B Series MSD Operating Manual

CI repeller

G7077-20432

CI filament- 2PK

G7005-60072

Dummy filament

G1999-60454

Washer spring curved 2.2 mm-ID 4.5 mm-OD, Qty. 2

3050-1374

Flat washer

3050-9082

Not shown

Package, GC/MS source Clamshell

G7002-80008

Not shown

Bracket, GC/MS source, Clamshell

G7002-00008

Not shown

CI source assembly

G7002-67404

Not shown

CI source assembly (without tip seal)

G7077-67404

Table 25 Parts list for CI source (

Figure 80

) (continued)

Item

Description

Part number

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands