manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

6

Operating in CI Mode

To Perform an NCI Autotune (Methane Reagent Gas)

5977B Series MSD Operating Manual

161

To Perform an NCI Autotune (Methane 
Reagent Gas)

Procedure

1

From the 

Tune and Vacuum Control

 view, load 

NCICH4.U

 (or an existing tune 

file for the reagent gas you are using).

2

From the 

Setup

 menu, select the 

CI Tune Wizard

 and follow the system 

prompts.

Accept the default temperature and other settings.

If you use an existing tune file, be sure to save it with a new name if you 
don’t want to overwrite the existing values. 

3

Under the 

Tune

 menu, click 

CI Autotune

.

There are no tune performance criteria. If autotune completes, it passes. (See 

Figure 53

 on page 162.) If the tune sets the EMV at or above 2,600 V, however, 

you may not be able to acquire data successfully if your method sets EMV to 
“+400” or higher.

CAUTION

Always verify MSD performance in EI before switching to CI operation. (See 

“To Verify EI System Performance” 

on page 131.) Always set up the CI MSD in 

PCI with methane as the reagent gas first, even if you are going to be using a 
different reagent gas or going to run NCI.

CAUTION

Avoid tuning unless absolutely necessary; this will minimize PFDTD 
background noise and help prevent ion source contamination.

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Water Factory Systems N4000 Series Installation, Operation And Maintenance Manual preview
N4000 Series
Brand: Water Factory Systems Pages: 15
A.O. Smith GPS-75 Owner'S Manual preview
GPS-75
Brand: A.O. Smith Pages: 20
A.O. Smith EES - 120 Specification Sheet preview
EES - 120
Brand: A.O. Smith Pages: 4
A.O. Smith BTX-80 Operation Manual preview
BTX-80
Brand: A.O. Smith Pages: 24
A.O. Smith BTI - 100 Specifications preview
BTI - 100
Brand: A.O. Smith Pages: 6
A.O. Smith BTF-80 Replacement Parts List preview
BTF-80
Brand: A.O. Smith Pages: 2
A.O. Smith ATI-305-N Specification Sheet preview
ATI-305-N
Brand: A.O. Smith Pages: 2
xFyre 300A Installation & Operating Instructions Manual preview
300A
Brand: xFyre Pages: 60
A.O. Smith 400A Replacement Parts List Manual preview
400A
Brand: A.O. Smith Pages: 8
A.O. Smith 400A Replacement Parts List preview
400A
Brand: A.O. Smith Pages: 4
A.O. Smith 104 Series Replacement Parts List Manual preview
104 Series
Brand: A.O. Smith Pages: 6
A.O. Smith 300A Owner'S Manual preview
300A
Brand: A.O. Smith Pages: 40
Kärcher BP 2 Garden Quick Start Manual preview
BP 2 Garden
Brand: Kärcher Pages: 8
A.O. Smith TWI 35-130 Instruction Manual preview
TWI 35-130
Brand: A.O. Smith Pages: 62
Lennox Signature XP19-024 Installation Instructions Manual preview
Signature XP19-024
Brand: Lennox Pages: 32
EMI S2H Specification Sheet preview
S2H
Brand: EMI Pages: 5
Warren rupp Sandpiper S05 Service & Operating Manual preview
Sandpiper S05
Brand: Warren rupp Pages: 22
Navien NPE-180A2 Installation Manual preview
NPE-180A2
Brand: Navien Pages: 131

Brands by name

Popular brands

Load more brands