Agilent Technologies 5977B CI MSD Operating Manual Download Page 48 | Manualshive

Page: 48 / 254

background image

2

Installing 8890 GC Columns



To Install a Capillary Column in the GC/MSD Interface Using a Standard Column Nut

48

5977B Series MSD Operating Manual

Procedure

1

Condition the column. (See

“To Condition a Capillary Column”

2

Vent the MSD and open the analyzer chamber. (See

“To Vent the MSD”

“To Open the Analyzer Chamber”

on page 176.) Be sure you

can see the end of the GC/MSD interface.

3

If installed, remove the knurled tip seal retainer, interface tip seal, and spring
from the end of the GC/MSD interface.

4

Slide an interface nut and conditioned ferrule onto the free end of the GC
column. The tapered end of the ferrule must point towards the nut.

5

Slide the column into the GC/MSD interface.

6

Use the column cutter to score the column 2 cm from the end.

7

While holding the column against the column cutter with your thumb, break
the column against the edge of the column cutter.

8

Inspect the end for jagged edges or burrs. If the break is not clean and even,
repeat steps 6 and 7.

9

Wipe the end with alcohol.

CAUTION

Always wear clean gloves while handling any parts that go inside the GC or the
analyzer chambers.

WARNING

The analyzer, GC/MSD interface, and other components in the analyzer
chamber operate at very high temperatures. Do not touch any part until you
are sure it is cool.

WARNING

Dangerous voltages exist inside the analyzer chamber, which can result in
fatal injury. Do not open the analyzer chamber door for any reason. If access is
ever required, trained service personnel must first disconnect the instrument
from the building power source.

WARNING

The GC operates under high temperatures. Do not touch any GC parts unless
you are certain they are cool.

CAUTION

Do not break the column off inside the vacuum manifold. Pieces of column
could fall or be pulled into the turbo pump and damage it.

«
...
46
47
48
49
50
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: Fedders Pages: 4

Brand: SAER Elettropompe Pages: 72

Brand: EINHELL Pages: 44

SUPER T T6A60S-4LE2X FT4 Series

Brand: GORMAN-RUPP PUMPS Pages: 48

Brand: Bryant Pages: 4

Brand: Lochinvar Pages: 1

Brand: KSB Pages: 62

Brand: Nibe Pages: 84

Brand: STIEBEL ELTRON Pages: 56

Brand: Pfeiffer Vacuum Pages: 30

Brand: Fluke Pages: 2

Altherma 3 ECH2O

Brand: Daikin Pages: 68

Brand: Hellenbrand Pages: 2

FLYGT Flygt 2071

Brand: Xylem Pages: 46

Brand: A.O. Smith Pages: 4

Brand: Varian Pages: 45

Brand: Makita Pages: 109

MAA1020H-MAA1024H MAA1030H

Brand: Marvair Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands