Agilent Technologies 5977B CI MSD Operating Manual Download Page 136 | Manualshive

Page: 136 / 254

background image

5

Operating in EI Mode



To Vent the MSD

136

5977B Series MSD Operating Manual

To Vent the MSD

Agilent MassHunter GC/MS Acquisition software allows you to specify
parameters in a GC method that will automate and speed up the vent process if
direct communication (DCOMM) with the GC is established. You must predefine
a Fast Vent method to use this option. See the Agilent MassHunter GC/MS
Acquisition software Online Help for information on how to configure a Fast Vent
method.

Procedure

Agilent recommends that you create and save a Vent method, to ensure that
safe temperatures are applied to the GC/MSD interface and MSD.

1

If you do not have LVDS or DCOMM communication between the GC and
MSD, in

Instrument Control

view select

GC Parameters

from the

Instrument

menu to display the

GC Edit Parameters

dialog. Select

Oven

, and set the oven

temperature to room temperature. Also select

Aux Heaters (MSD Transfer

line) and Inlets

, and set those temperatures to room temperature. Click

OK

to

close the dialog and send this temperature to the GC.

WARNING

If hydrogen is used as a carrier gas or JetClean system supply, the carrier and
JetClean system supply shutoff valves must be closed before turning off the
MSD power. If the foreline pump is off, hydrogen will accumulate in the MSD
and an explosion may occur. Read

“Hydrogen Safety”

on page 24 before

operating the MSD with hydrogen gas.

CAUTION

Ensure the GC oven and the GC/MSD interface are cool before turning off
carrier gas flow to prevent damage to the column.

«
...
134
135
136
137
138
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: Samsung Pages: 27

Brand: Vector Pages: 8

Clima Canal JDPC.002

Brand: Jaga Pages: 8

Brand: SMC Networks Pages: 19

Brand: Watts Pages: 73

Brand: Wacker Neuson Pages: 70

20:1 KING 231131

Brand: Graco Pages: 18

Brand: OSO Pages: 16

Brand: Black Knight Pages: 15

Brand: GORMAN-RUPP PUMPS Pages: 31

Brand: Gardenline Pages: 2

Brand: OmarLift Pages: 28

Brand: Cosmo Pages: 48

MULTIDRAIN UV 305-1

Brand: Pentair Jung Pumpen Pages: 40

Brand: Macnaught Pages: 24

Brand: KAMMAK Pages: 8

Brand: Airetool Pages: 20

Brand: Uni-max Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands