Agilent Technologies 5977B CI MSD Operating Manual Download Page 45 | Manualshive

Page: 45 / 254

background image

2

Installing 8890 GC Columns



To Install a Capillary Column in the GC/MSD Interface Using the Self-Tightening Column Nut

5977B Series MSD Operating Manual

45

11

Hand-tighten the nut. (See

.) Ensure the position of the column does

not change as you tighten the nut. Do not over tighten the nut.

12

Tighten the nut in the clockwise direction. Continue to tighten until you feel
the ferrule grip the column.

13

Check the GC oven to ensure that the column does not touch the oven walls.

Figure 7.

Installing a capillary column in the GC/MSD interface

14

Install the spring, tip seal, and knurled tip seal retainer on the GC/MSD
interface. (See

“To Install the GC/MSD Interface Tip Seal”

on page 50.) Do

not use the tip seal, spring, and knurled tip seal retainer with an EI SS or Inert
source. The interface socket on these sources does not allow the tip seal
installation to fit. (See

CAUTION

Use care when placing the tip seal on the GC/MSD interface to avoid
damaging the column.

CAUTION

Forcing the analyzer door closed if these parts are misaligned will damage the
tip seal or the interface or the ion source, or will keep the sideplate from
sealing.

«
...
43
44
45
46
47
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: Gator Prime Pages: 32

Brand: A.O. Smith Pages: 62

Brand: MasterCraft Pages: 8

Brand: T.I.P. Pages: 136

Brand: Sierra Pages: 11

Brand: VONROC Pages: 60

Basement Sentry 507

Brand: Zoeller Pages: 8

Brand: Gianneschi Pages: 28

Brand: Zodiac Pages: 32

Brand: Oase Pages: 7

Lincoln 215-M049

Brand: SKF Pages: 45

Brand: Wacker Neuson Pages: 123

Brand: Xylem Pages: 21

Brand: Marco Pages: 3

Brand: Trinity Lx Pages: 24

Brand: Grundfos Pages: 153

Brand: Jebao Pages: 3

Brand: Calpeda Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands