Agilent Technologies 5977B CI MSD Operating Manual Download Page 40

Page: 40 / 254

Installing 8890 GC Columns



To Install a Capillary Column in a Split/Splitless Inlet

5977B Series MSD Operating Manual

Slide the septum up to the bottom of the nut to fix the correct column
insertion length.

Insert the column in the inlet.

Slide the nut up the column to the inlet base, and finger-tighten the nut.

Adjust the column position so the septum is even with the bottom of the
column nut.

Tighten the column nut an additional 1/4 to 1/2 turn. The column should not
slide with a gentle tug.

Start carrier gas flow.

Verify flow by submerging the free end of the column in isopropanol. Look for
bubbles.

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands