Agilent Technologies 5977B CI MSD Operating Manual Download Page 150

Page: 150 / 254

Operating in CI Mode



To Set Up the Software for CI Operation

150

5977B Series MSD Operating Manual

•

Ion polarity

: Always set up in PCI with methane first, then switch to your

desired ion polarity and reagent gas.

•

Abundance target

: Adjust higher or lower to get the desired signal

abundance. Higher signal abundance also gives higher noise abundance.
This is adjusted for data acquisition by setting the EMV in the method.

•

Peakwidth target

: Higher peakwidth values give better sensitivity, lower

values give better resolution.

•

Maximum emission

current

Optimum emission current maximum for NCI is

very compound-specific and must be selected empirically. Optimum
emission current for pesticides, for example, may be about 200 µA.
Maximum current limit is 200 µA for EI and 250 µA for CI.

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands