Agilent Technologies 5977B CI MSD Operating Manual Download Page 184

Page: 184 / 254

General Maintenance



To Clean the EI HES

184

5977B Series MSD Operating Manual

To Clean the EI HES

Materials needed

•

Abrasive paper (5061-5896)

•

Alumina abrasive powder (393706201)

•

Aluminum foil, clean

•

Cloths, clean (05980-60051)

•

Cotton swabs (5080-5400)

•

Glass beakers, 500 mL

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Solvents

•

Methanol (reagent-grade)

•

Methylene chloride (reagent-grade)

•

Acetone (reagent-grade)

•

Ultrasonic bath

Procedure

Disassemble the EI HES. (See

“To Disassemble the EI HES”

on page 181.)

Collect the following parts to be cleaned: (See

Figure 58

on page 185.)

•

Filament mount

•

Source mount (does not get abrasively or ultrasonically cleaned)

•

Repeller

•

Source body

•

Extractor lens (5)

•

Post extractor lens 1 (4)

•

Post extractor lens 2 (3)

•

Ion focus lens (2)

•

Entrance lens (1)





Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands