Graco Husky 307 F Series Instructions-Parts List Manual Download | Manualshive

Page: 1 / 36

background image

01428B

Instructions - Parts List

ACETAL AND POLYPROPYLENE

Husky



307 Air-Operated

Diaphragm Pumps

308553ZAE

EN

For pumping transfer applications. For professional use only.

Only pumps with acetal fluid sections are approved for use in European explosive
atmosphere locations.

100 psi (0.7 MPa, 7 bar) Maximum Fluid Working Pressure
100 psi (0.7 MPa, 7 bar) Maximum Air Input Pressure

*Model No. D31 ___ Acetal Pumps**, Series F

*Model No. D32 ___ Polypropylene Pumps, Series F

*Model No. D3A ___ Acetal BSPT Pumps**, Series F

*Model No. D3B ___ Polypropylene BSPT Pumps, Series F

* To determine the Model No. for your pump and for additional models, refer to the Pump Matrix on page 26.

** Pumps with Acetal fluid sections are certified:

Important Safety Instructions

Read all warnings and instructions in this
manual. Save these instructions.

II 2 GD

Ex h IIC 66°...135°C Gb
Ex h IIIC T135°C Db

ATEX T-code rating is dependent on the temperature
of the fluid being pumped. Fluid temperature is limited
by the materials of the pump interior wetted parts.
See Technical Data for the maximum fluid operating
temperature for your specific pump model.

Tel: 866-777-6060
Fax: 866-777-6383

Springer Pumps, LLC

Website: www.springerpumps.com

Int'l: +001 267 404 2910

1
2
3
...
»

Summary of Contents for Husky 307 F Series





































Reviews:

No comments

Related manuals for Husky 307 F Series

Evosta2 11/139 SAN V

Brand: DAB Pages: 31

Brand: DAB Pages: 19

Brand: Danfoss Pages: 72

Brand: Danfoss Pages: 91

DHP-H Varius Pro+

Brand: Danfoss Pages: 12

Brand: YAMADA Pages: 18

Brand: Gamo Pages: 25

Brand: Gamma Vacuum Pages: 27

aroSTOR VWL B 200/5 UK

Brand: Vaillant Pages: 24

Brand: Vaillant Pages: 20

Brand: Vaillant Pages: 24

Brand: Zip Pages: 16

Bell & Gossett Domestic 616PF

Brand: Xylem Pages: 4

Brand: Sanden Pages: 48

BlackFin CT-2902BPHP

Brand: Panduit Pages: 68

Alterma EDHQ011AA6V3

Brand: Daikin Pages: 22

Brand: Comet Pages: 12

Brand: Warren rupp Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands