3Com VCX V7000 Page 208 Maintenance Manual Download | Manualshive

Page: 208 / 344

background image

208

A

PPENDIX

A: U

PGRADING

VCX S

ERVER

S

OFTWARE

F

ROM

V7.0

TO

V7.1

vcx-all-7.1.3c.tar)

that will replace the current version. The letter

c

is

always appended to the version number.

3

To start the upgrade process, enter the following commands:

cd /opt/installtemp

tar xvf vcx-all-7.1.

x

c.tar

cd upgrade-7.1.

x

c

./install-upgrade

The system may prompt you to confirm that a new operating system
version will be installed and indicates which disk partition will be used
after the upgrade. If you see such a prompt, answer

y.

The system displays several status messages. The last two messages are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.1.

x

c is now available -------------------

4

Switch to the new software version by entering the following command:

vcx-switchversion 7.1.

x

c

The system displays several status messages and provides prompts that
allow you enable Adhoc Conferencing, UPS Monitoring, and Global
Voicemail Integration.

5

The Adhoc Conferencing prompt appears:

In order to support "ad-hoc" conferences with more than 3

participants, the Adhoc Conference Service is used. This

service should be enabled on this server, unless another

server dedicated to Adhoc Conferencing will be used instead.

If available, a separate server typically provides greater

capacity and may be shared among sites.

Use the Adhoc service on this server? (Y/N) [Y] :

If you want this server to act as a multi-caller (up to 6 callers)
conferencing server, enter

y

. If not, enter

n

.

6

The UPS Monitoring prompt appears:

An Uninterruptible Power Supply (UPS) can be used with VCX

systems to avoid disruption due to a power outage. VCX

provides a UPS monitoring service which tracks the UPS's

status and performs a safe shutdown when the its battery is

depleted during a long power outage. To use this feature,

you must have a compatible UPS installed and configured in

accordance with the VCX documentation.

Enable UPS monitoring? [N] :

«
...
206
207
208
209
210
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Galaxy S Blaze 4G

Brand: Samsung Pages: 4

Galaxy S Blaze 4G

Brand: Samsung Pages: 27

Galaxy S 4 mini

Brand: Samsung Pages: 26

GALAXY S GT-I9000

Brand: Samsung Pages: 132

Galaxy S Aviator

Brand: Samsung Pages: 56

Galaxy Note20 Ultra 5G

Brand: Samsung Pages: 2

Galaxy Note20 5G

Brand: Samsung Pages: 2

Brand: Samsung Pages: 41

Brand: Samsung Pages: 2

Brand: Samsung Pages: 28

Brand: Samsung Pages: 65

Brand: Samsung Pages: 7

Brand: Samsung Pages: 109

GALAXY Note 8.0

Brand: Samsung Pages: 51

Brand: Samsung Pages: 36

Brand: Samsung Pages: 68

Brand: Samsung Pages: 17

Brand: Federal Signal Corporation Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands