3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 184 / 344

background image

184

A

PPENDIX

A: U

PGRADING

VCX S

ERVER

S

OFTWARE

F

ROM

V7.0

TO

V7.1

feature's operation. Typically the Central Servers are at

one of the regional sites.

Is this a Central Server for Global Voicemail? [N] :

If this server has been configured as a Global Voicemail Central Server,
enter y and go to step 5.

If you answer

n

to indicate that this is not a Central Server, you will be

prompted to enter the Central Server IP address.

5

After completing the UPS Monitoring and Global Voicemail Integration
prompts, the server reboots. When the reboot process has been
completed, the system starts VCX 7.1.

x

services.

6

After the system has completed the restart process, verify that the
upgrade has occurred by entering this command:

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX
software (7.1.

x

c). If the link does not point to the new version, wait a few

minutes and reenter the command. This could take several minutes and it
is important the link pointer is correct before proceeding.

Example Output

/opt/3com/VCX -> /opt/3com/VCX.7.1.

x

c

Upgrading the

Secondary IP

Telephony Server

Follow the steps in this section to upgrade the secondary IP Telephony
server.

1

To start the upgrade process, enter these commands on the secondary IP
Telephony server:

cd /opt/installtemp

tar xvf vcx-softswitch-7.1.

x

c.tar

cd upgrade-7.1.

x

c

./install-upgrade

The system may prompt you to confirm that a new operating system
version will be installed and indicates which disk partition will be used
after the upgrade. If you see such a prompt, answer

y.

The system displays several status messages. The last two messages are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.1.

x

c is now available -------------------

«
...
182
183
184
185
186
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Neoi Pages: 40

Brand: Yealink Pages: 87

Brand: D-Link Pages: 56

Brand: Samsung Pages: 24

Scopia XT5000 Series

Brand: RADVision Pages: 184

Brand: Samsung Pages: 139

Brand: TCT Mobile Pages: 64

Brand: Alcatel Pages: 67

Brand: Dash Pages: 24

Brand: Micromax Pages: 22

Brand: Majestic Pages: 57

Brand: Audiovox Pages: 61

Brand: Sony Ericsson Pages: 40

Home SmartPhone

Brand: BT Pages: 8

Brand: Nortel Pages: 112

Technophone PC200

Brand: Audiovox Pages: 12

Brand: Xorcom Pages: 2

StarLink SLE-LTEV-SS

Brand: NAPCO Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands