3Com VCX V7000 Maintenance Manual Download

Page: 136 / 344

136

HAPTER

8: M

ANAGING

NINTERRUPTIBLE

OWER

UPPLIES

The optional argument

--fullauto

specifies that the command should

run in automatic mode. In this mode, command execution does not
provide any interactive prompts or queries.

Note that you can enter the

vcx-ups-setup

command with the optional

--help

argument to display information on command usage.

Monitoring UPS
Status

This section describes how to check the status of a UPS

You can use the

vcx-ups-status

command to check the status of any

UPS in your local VCX system, or the status of a UPS in a remote VCX
system. You can enter the command on the master server or any slave
server. The

vcx-ups-status

command uses the following syntax:

vcx-ups-status (ups0 | ups1)[master-ip] [--parameter]

You must identify the UPS you want to monitor. For a single UPS system,
enter

ups0

. For a dual UPS system, enter either

ups0

ups1

, depending

on the UPS you want to monitor.

The parameter

master-ip

is optional. Use this parameter to specify the IP

address of a remote VCX UPS master server.

In addition to the required parameter

ups0

ups1

, you must enter one

of the parameters shown in

Table 10

Table 10

vcx-ups-status Command Parameters

Parameter

Description

--upsstatus

Indicates the status of the UPS, for example

online

offline

--upsload

Indicates the load, expressed in watts, placed on the UPS by
the attached VCX servers.

--upsmfr

Displays the name of the UPS manufacturer. In this case, the
value is always

APC

--batterycharge

Indicates, as a percentage, the current battery charge.

--upsserial

Displays the manufacturer’s serial number of the UPS.

--upsmodel

Displays the manufacturer’s model name of the UPS.

--isconfig

Indicates whether or not (

) the UPS has been

configured.

Summary of Contents for VCX V7000

























































































































































































































































































































































Search results

Summary of Contents for VCX V7000

Reviews:

Related manuals for VCX V7000

Brands by name

Popular brands

3Com VCX V7000, Maintenance Manual

Search results

Summary of Contents for VCX V7000

Reviews:

Related manuals for VCX V7000

Brands by name

Popular brands