3Com VCX V7000 Page 199 Maintenance Manual Download | Manualshive

Page: 199 / 344

background image

Upgrading a Multi-Site VCX System with Branch Offices

199

Telephony and Messaging Server

for more information. In this

example, there is one Master site, Region 2.

c

The

Enter the MASTER DEFINITION SITE IP Address [

IP

address

]

prompt appears.

Enter the IP address of the Master Definition site. This is the IP address
of the eth0 interface on this server (the Authentication and Directory
server in Region 1).

d

The

Enter the MASTER SITE 1 IP Address [0.0.0.0]

prompt

appears.

Enter the IP address of the Master Site. This is the IP address of the
eth0 interface on the Authentication and Directory server in Region 2.
If there are more than one Master Sites, this question repeats until the
number of master sites specified in step

b

is reached.

e

The

Do you want to continue with the above settings? [n/y]:

prompt appears.

Enter

y

to continue. The script executes.

When the replication is complete,

Multi-Master Replication Status

is

reported as

NORMAL

. Do not continue to the next step on this server

until the replication is complete. Note that replication can take
approximately 20 minutes to complete.

f

You can check the replication by entering the following command:

./checkReplication

6

Set up database replication on Region 2 by entering the following
commands (you should still be logged in to the Authentication and
Directory server as

cworks

):

cd /opt/3com/VCX/vcxdata/bin

./setupReplication

The replication setup script starts. Follow these steps:

a

The

Enter the VCX Site Identification i.e. Site Id

prompt

appears.

Enter site ID configured for Region 2.

b

The

Enter the Number of MASTER SITEs other than the MASTER

DEFINITION SITE

: prompt appears.

Enter the number of Master sites. To determine the number of Master
Sites associated with this office, use the

listVcxdata

command. See

Manually Configuring Replication for an IP Telephony Server or IP

«
...
197
198
199
200
201
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Damall Pages: 7

Brand: Samsung Pages: 135

blackview Crown

Brand: Iget Pages: 76

Brand: Unitech Pages: 72

8110 - Pearl - AT&T

Brand: Blackberry Pages: 54

Blackview GBV7100

Brand: Iget Pages: 62

Brand: Aastra Pages: 22

Brand: FLY Pages: 56

Brand: TECNO MOBILE LIMITED Pages: 6

Brand: Zonda Pages: 27

Brand: Samung Pages: 150

Brand: H3C Pages: 12

Flash Mini 4031D

Brand: OneTouch Pages: 21

Brand: Pacific GSM Pages: 8

Brand: ATL Pages: 4

Brand: Alcatel Pages: 58

Brand: Samsung Pages: 208

Brand: Samsung Pages: 203

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands