3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 206 / 344

background image

206

A

PPENDIX

A: U

PGRADING

VCX S

ERVER

S

OFTWARE

F

ROM

V7.0

TO

V7.1

cd /opt/installtemp

tar xvf vcx-bss-7.1.

x

c.tar

cd upgrade-7.1.

x

c

./install-upgrade

The system may prompt you to confirm that a new operating system
version will be installed and indicates which disk partition will be used
after the upgrade. If you see such a prompt, answer

y.

The system displays several status messages. The last two messages are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.1.

x

c is now available -------------------

4

Change to the new software version by entering this command:

vcx-switchversion 7.1.

x

c

The system displays several status messages and provides prompts that
allow you enable UPS Monitoring.

5

The UPS Monitoring prompt appears:

An Uninterruptible Power Supply (UPS) can be used with VCX

systems to avoid disruption due to a power outage. VCX

provides a UPS monitoring service which tracks the UPS's

status and performs a safe shutdown when the its battery is

depleted during a long power outage. To use this feature,

you must have a compatible UPS installed and configured in

accordance with the VCX documentation.

Enable UPS monitoring? [N] :

If you do not have a UPS installed and enter

n

(or press

Enter

); the

remaining UPS configuration prompts are not displayed.

If you do have a UPS installed and enter

y

and see

Configuring UPS

for information on the subsequent UPS configuration

prompts.

6

After completing the UPS Monitoring prompts, the server reboots. When
the reboot process has been completed, the system starts VCX 7.1.

x

services.

After the system has completed the restart process, verify that the
upgrade has occurred by entering the following command:

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX
software (7.1.

x

c). If the link does not point to the new version, wait a few

«
...
204
205
206
207
208
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Raco Pages: 21

Brand: Alcatel Pages: 44

Brand: Ratel Pages: 2

Brand: Yealink Pages: 8

Sensation 4G T-Mobile

Brand: HTC Pages: 38

8100 SMARTPHONE

Brand: Blackberry Pages: 230

Brand: Plum Mobile Pages: 15

Brand: iBall Slide Pages: 63

Brand: Samsung Pages: 127

Brand: Xiaomi Pages: 8

X-style 33 Steel

Brand: Sigma Pages: 17

Brand: Nokia Pages: 34

Brand: Hi-Tech Pages: 12

Brand: GENERAL MOBILE Pages: 16

Brand: Broadconnect Pages: 84

Brand: Starcom Systems Pages: 5

Brand: Nokia Pages: 105

Brand: Commtiva Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands