3Com VCX V7000 Maintenance Manual Download

Page: 185 / 344

Upgrading a Single-Site System With Four Servers

185

Switch to the new software version by entering the following command:

vcx-switchversion 7.1.

The system displays several status messages and provides prompts that
allow you enable Adhoc Conferencing and UPS Monitoring.

The Adhoc Conferencing prompt appears:

In order to support "ad-hoc" conferences with more than 3

participants, the Adhoc Conference Service is used. This

service should be enabled on this server, unless another

server dedicated to Adhoc Conferencing will be used instead.

If available, a separate server typically provides greater

capacity and may be shared among sites.

Use the Adhoc service on this server? (Y/N) [Y] :

If you want this server to act as a multi-caller (up to 6 callers)
conferencing server, enter

. If not, enter

The UPS Monitoring prompt appears:

An Uninterruptible Power Supply (UPS) can be used with VCX

systems to avoid disruption due to a power outage. VCX

provides a UPS monitoring service which tracks the UPS's

status and performs a safe shutdown when the its battery is

depleted during a long power outage. To use this feature,

you must have a compatible UPS installed and configured in

accordance with the VCX documentation.

Enable UPS monitoring? [N] :

If you do not have a UPS installed and enter

(or press

Enter

); the

remaining UPS configuration prompts are not displayed.

If you do have a UPS installed and enter

and see

Configuring UPS

Monitoring

for information on the subsequent UPS configuration

prompts.

After completing the Adhoc Conferencing and UPS Monitoring prompts,
the server reboots. When the reboot process has been completed, the
system starts VCX 7.1.

services.

After the system has completed the restart process, verify that the
upgrade has occurred by entering this command:

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX
software (7.1.

c). If the link does not point to the new version, wait a few

Summary of Contents for VCX V7000

























































































































































































































































































































































Search results

Summary of Contents for VCX V7000

Reviews:

Related manuals for VCX V7000

Brands by name

Popular brands

3Com VCX V7000, Maintenance Manual

Search results

Summary of Contents for VCX V7000

Reviews:

Related manuals for VCX V7000

Brands by name

Popular brands