3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 249 / 344

background image

Upgrading a Multi-Site VCX System with Branch Offices

249

vcx-all-7.1.3c.tar)

that will replace the current version. The letter

c

is

always appended to the version number.

3

To start the upgrade process, enter the following commands:

cd /opt/installtemp

tar xvf vcx-softswitch-7.1.

y

c.tar

cd upgrade-7.1.

y

c

./install-upgrade

The system may prompt you to confirm that a new operating system
version will be installed and indicates which disk partition will be used
after the upgrade. If you see such a prompt, answer

y.

The system displays several status messages. The last two messages are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.1.

y

c is now available -------------------

4

Switch to the new software version by entering the following command:

vcx-switchversion 7.1.

y

c

The system displays several status messages and then reboots. After the
the reboot process has been completed, the system starts VCX 7.1.

y

services.

5

After the system has completed the restart process, verify that the
upgrade has occurred by entering this command:

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX
software (7.1.

y

c). If the link does not point to the new version, wait a few

minutes and reenter the command. This could take several minutes and it
is important the link pointer is correct before proceeding.

Example Output

/opt/3com/VCX -> /opt/3com/VCX.7.1.

y

c

6

Repeat steps 1 through 5 for all the other branch office servers in
Region 2.

«
...
247
248
249
250
251
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Hama Pages: 12

Brand: Samsung Pages: 2

Brand: O2 Pages: 72

EasyFlip OLT2908

Brand: Olitech Pages: 57

SPH-A600 Series

Brand: Samsung Pages: 111

Brand: HIKVISION Pages: 2

Brand: Rath Pages: 9

Emergency Phone Dialer

Brand: Radio Shack Pages: 20

Brand: Micromax Pages: 18

Brand: Paragon Pages: 80

Brand: Allview Pages: 30

OPENTOUCH ALE-300

Brand: Alcatel-Lucent Pages: 101

Brand: Samsung Pages: 184

Brand: Samsung Pages: 184

Brand: IPRO Pages: 32

Brand: myPhone Pages: 41

Brand: Philips Pages: 28

Brand: Lava Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands