background image

284

A

PPENDIX

 C: U

PGRADING

 VCX S

ERVER

 S

OFTWARE

 F

ROM

 V6.0 

TO

 V7.0

The system may prompt you to confirm that a new operating system 
version will be installed and indicates which disk partition will be used 
after the upgrade. If you see such a prompt, answer 

y.

The system displays several status messages. The last two messages 
are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.0.

x

c is now available -------------------

b

Obtain a license key for the server. Se

Obtaining a License Key File

.

c

Install the license key. See 

Installing a License Key File

.

d

Switch to the new software version by entering the following 
command:

vcx-switchversion 7.0.

x

The system displays several status messages and then reboots. After 
the reboot process has been completed, the system starts VCX 7.0.

x

 

Call server.

e

After the system has completed the restart process, verify that the 
upgrade has occurred by entering this command:

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX 
software (7.0.

x

c).

Example Output

/opt/3com/VCX -> /opt/3com/VCX.7.0.

x

4

Upgrade the secondary Call server by following the procedure described 
in step 3.

5

Repeat steps for the other regions in your VCX system.

Upgrading the

Regional Call Records

Server

This section describes how to upgrade regional Call Records server. In a 
multi-site VCX system, a single Call server typically supports all regional 
offices. You need to perform the steps in this section on a console 
attached to the regional Call server.

To upgrade the Call Records server:

1

Log in to the Call Records server as 

root

.

2

Obtain a copy of the 

vcx-bss-7.0.

x

c.tar

 software upgrade file and 

place it in the 

/opt/installtemp

 directory on the Call Records server.

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews: