3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 237 / 344

background image

Upgrading a Multi-Site VCX System with Branch Offices

237

5

Enter the following command to exit the

cworks

account and return to

the

root

account:

exit

6

Obtain a copy of the

vcx-dataserver-7.1.

y

c.tar

software upgrade file

and place it in the

/opt/installtemp

directory on the Authentication

and Directory server. The variable

y

indicates the version of VCX software

(for example,

vcx-all-7.1.3c.tar)

that will replace the current version.

The letter

c

is always appended to the version number.

7

Enter these commands:

cd /opt/installtemp

tar xvf vcx-dataserver-7.1.

y

c.tar

cd upgrade-7.1.

y

./install-upgrade

The system may prompt you to confirm that a new operating system
version will be installed and indicates which disk partition will be used
after the upgrade. If you see such a prompt, answer

y.

The system displays several status messages. The last two messages are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.1.

y

c is now available -------------------

8

Change to the new software version by entering this command:

vcx-switchversion 7.1.

y

c

The system displays several status messages and then reboots. When the
reboot process has been completed, the system starts VCX 7.1.

y

c

Authentication and Directory service.

9

After the system has completed the restart process, verify that the
upgrade has occurred by entering the following command:

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX
software (7.1.

y

c). If the link does not point to the new version, wait a few

minutes and reenter the command. This could take several minutes and it
is important the link pointer is correct before proceeding.

Example Output:

/opt/3com/VCX -> /opt/3com/VCX.7.1.

y

c

10

Enter the following commands to stop the Authentication and Directory
server on Region 1:

cd /opt/3com/VCX/scripts/rc3.d

./S20vcxdata stop

«
...
235
236
237
238
239
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: D-Link Pages: 56

Brand: Hama Pages: 12

Brand: O2 Pages: 72

Scopia XT5000 Series

Brand: RADVision Pages: 184

Yealink SIP-T48G

Brand: Yealink Pages: 9

Yealink SIP-T42G

Brand: Yealink Pages: 2

8700 - 8707H SMARTPHONE

Brand: Blackberry Pages: 48

Brand: RATH MICROTECH Pages: 2

Brand: Grandstream Networks Pages: 25

Smartphone E-11

Brand: Etisalat Pages: 75

Brand: Alcatel-Lucent Pages: 60

Vertis 2211 easy

Brand: Overmax Pages: 80

WirelessIP 3000

Brand: Hitachi Cable Pages: 132

Brand: Lanix Pages: 21

Brand: Zte Pages: 11

Brand: Zte Pages: 198

Brand: ipLDK Pages: 8

Brand: Zte Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands