3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 246 / 344

background image

246

A

PPENDIX

B: U

PGRADING

VCX S

ERVER

S

OFTWARE

F

ROM

V7.1.

X

TO

V7.1.

Y

4

Upgrade the secondary Call server by following the procedure described
in step 3.

Upgrading the

Regional Call Records

Server

This section describes how to upgrade regional the Call Records server. In
a multi-site VCX system, a single Call server typically supports all regional
offices. You need to perform the steps in this section on a console
attached to the regional Call server.

To upgrade the Call Records server:

1

Log in to the Call Records server as

root

.

2

Obtain a copy of the

vcx-bss-7.1.

y

c.tar

software upgrade file and

place it in the

/opt/installtemp

directory on the Call Records server.

3

Enter these commands:

cd /opt/installtemp

tar xvf vcx-bss-7.1.

y

c.tar

cd upgrade-7.1.

y

c

./install-upgrade

The system may prompt you to confirm that a new operating system
version will be installed and indicates which disk partition will be used
after the upgrade. If you see such a prompt, answer

y.

The system displays several status messages. The last two messages are:

------------------- Installation Completed Successfully -------------------

------------------- VCX version 7.1.

y

c is now available -------------------

4

Change to the new software version by entering this command:

vcx-switchversion 7.1.

y

c

The system displays several status messages and then reboots. When the
reboot process has been completed, the system starts VCX 7.1.

y

c

services.

5

After the system has completed the restart process, verify that the
upgrade has occurred by entering the following command:

ls -l /opt/3com/VCX

The symbolic link (VCX) should point to the new version of the VCX
software (7.1.

y

c). If the link does not point to the new version, wait a few

minutes and reenter the command. This could take several minutes and it
is important the link pointer is correct before proceeding.

Example Output:

/opt/3com/VCX -> /opt/3com/VCX.7.1.

y

c

«
...
244
245
246
247
248
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: TCL Pages: 22

Brand: Samsung Pages: 22

Brand: Facom Pages: 13

Brand: Olympia Pages: 54

Brand: Hanlong Pages: 57

T48G-SKYPE FOR BUSINESS EDITION

Brand: Yealink Pages: 12

Brand: Yealink Pages: 4

Brand: Yealink Pages: 16

Brand: Yealink Pages: 12

Brand: Yealink Pages: 3

Brand: Yealink Pages: 4

Brand: Yealink Pages: 8

Brand: Yealink Pages: 3

Brand: Yealink Pages: 4

Brand: Yealink Pages: 7

Brand: Yealink Pages: 2

Brand: Yealink Pages: 4

T48S Skype For Business Edition

Brand: Yealink Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands