York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 45 / 160

JOHNSON CONTROLS

SECTION 2 – OPTIVIEW CONTROL CENTER

FORM 160.79-O3

ISSUE DATE: 11/09/2018

HGBP Command

Indicates the Hot Gas Bypass Command 0% (Closed

to 100% (Open). Only displayed if Hot Gas option is

installed and enabled on the Operations screen.

Oil Pump Drive Command Frequency

Indicates the VSOP Drive Command Frequency, 0 Hz

to 60 Hz.

Vane Motor Switch (LED) (Open/Closed)

Illuminates when the compressor vanes are in the fully

closed position. When Off, indicates open.

Compressor Status

Displays whether compressor has been selected as the

lead or Lag compressor. The lead compressor is select-

ed upon receipt of a start signal. The compressor that

has the least amount of run time that is ready to run is

selected as the lead compressor.

% Full Load Amps

Displays compressor motor current as a percentage of

full load amps of the compressor motor.

PRV Opening (LED)

Illuminates when an open command is being applied to

the Pre-Rotation Vanes.

PRV Closing (LED)

Illuminates when an close command is being applied to

the Pre-Rotation Vanes.

PRV Position

Displays the position (0% to 100%) of the pre-rotation

vanes.

PRV Command

Displays the position command (0% to 100%) for the

pre-rotation vanes.

Discharge Valve Close Command (LED)

Illuminates when a close command is being applied to

the compressor Discharge Valve.

Discharge Valve Open Command (LED)

Illuminates when an open command is being applied to

the compressor Discharge Valve.

Discharge Valve

Indicates the status of the compressor Discharge Valve

as closing, closed, opening or opened.

High Pressure Switch

Indicates the status of the compressor High Pressure

Switch. (Open or Closed)

PROGRAMMABLE

Software does not allow manual Pre-rotation Vanes

control on a shutdown compressor while the other

compressor is running. This helps minimize rotation

of this compressor if its Discharge Valve is not fully

sealed.

Discharge Valve Control Mode (Manual/Auto)

Only displayed if the compressor is stopped. This key

puts the compressor Discharge Valve in manual or au-

tomatic operation. When in manual operation, this key

is used to manually open or close the valve.

NAVIGATION
Home

Causes an instant return to the Home Screen.

Compressor

Causes an instant return to the Main Compressor

Screen.

VGD

Access Level Required: SERVICE

Only displayed if VGD feature enabled on Operations

Screen. Moves to the subscreen that allows viewing

and programming of the Variable Geometry Diffuser

(VGD) feature for the compressor.

Proximity Probe Calibrate

Only available if chiller is stopped. Moves to the sub-

screen that allows calibration of the High Speed Thrust

Bearing Proximity Probe for the compressor.

PRV Calibrate

Only available if the chiller is stopped. Moves to the

subscreen that allows calibration and manual control of

the Pre-rotation Vanes for the compressor.

Capacity Control

Navigates to the Capacity Control screen.

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды