York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 91 / 160

JOHNSON CONTROLS

SECTION 2 – OPTIVIEW CONTROL CENTER

FORM 160.79-O3

ISSUE DATE: 11/09/2018

This screen displays information pertinent to the op-

tional Motor Monitoring feature. The feature is an ad-

ditional circuit board and sensors for each motor which

can monitor motor winding temperatures, motor bear-

ing temperatures, motor bearing vibration and provide

motor cooling coil leak detection if installed. The mo-

tor could be equipped with either RTD's or Thermis-

tors for winding and bearing temperature monitoring.

Motor cooling coil leak detection could be done with

either an optical or float type of sensor. This screen is

similar for both Motor 1 and Motor 2.

DISPLAY ONLY
Motor Run (LED)

Illuminates when the OptiView Control Center is com-

manding the motor to run.

% Full Load Amps

Displays the motor current as a percentage of chiller

Full Load Amps.

VSD Output Frequency

Only displayed when Motor Drive Type Setpoint is set

to any VSD type. Displays the frequency at which the

VSD is operating the motor. This value is provided by

the VSD Logic Board.

PRV Position

Displays the present Pre-rotation Vanes position as a

value between 0% (closed) and 100% (full open).

Motor Windings

Temperature

Displays the enabled Motor Winding Temperatures

for phase A, B and C. When winding RTD's are en-

abled, there are 2 temperatures displayed per phase. If

Thermistors are installed then only one temperature is

displayed per phase. If any sensor has failed and is dis-

abled, its reading will not be displayed. Any RTD sen-

sor that registers as an open is considered invalid and

displays as XXX.X.

Average Winding Temperature

This value is calculated as the average of all enabled

and valid Motor Winding Temperatures. Any winding

temperature that registers as open, out of range or dis-

abled is not used in the calculation. When RTD's are

used for winding temperature measurement, there are

a maximum of 6 temperatures used to calculate the av-

erage. When Thermistors are used, there are a maxi-

mum of 3 temperatures used to calculate the average.

The text description and data box do not appear when

the Winding Temperature Protection option is not in-

stalled.

MOTOR DETAILS SCREEN

FIGURE 32 -

MOTOR DETAILS SCREEN

LD27871

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды