York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 80 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen displays information pertaining to the

Low Voltage Variable Speed Drive (VSD), if installed.

There are two similar screens available: one for VSD 1

and another for VSD 2.

DISPLAY ONLY
Motor Run (LED)

Indicates whether the digital output from the controls is

commanding the motor to RUN.

Motor Heater (LED)

Indicates whether the digital output from the controls is

commanding the optional motor heater on. This LED is

not displayed if the option is not installed.

% Full Load Amps

Displays the motor current as a percentage of the Full

Load Amps (FLA) value.

Motor Current Limit Setpoint

Displays the current limit value in use. This value could

come from a 0 to 20 mA, 4 to 20 mA, 0 to 10 VDC or

2 to 10 VDC input in Analog Remote mode, PWM sig-

nal in Digital Remote mode, SC-EQ communications

interface in ISN (BAS) mode, or a locally programmed

value.

PRV Position

Displays the Pre-rotation Vane position as a value be-

tween 0 and 100%.

Pulldown Demand Time Left

Displays the time remaining in the programmed pull-

down period if the value is nonzero.

Output Voltage

Displays the output voltage measured to the motor.

Output Frequency

Displays the present output frequency to the motor.

Input Power

Displays the total kilowatts measured by the VSD or

Harmonic Filter, if installed.

KW Hours

Displays the cumulative amount of kilowatts used over

time as the VSD motor controller operates.

Output Current - Phase A, B, C

Displays the phase current measured to the motor.

LOW VOLTAGE VARIABLE SPEED DRIVE SCREEN

FIGURE 27 -

LOW VOLTAGE VARIABLE SPEED DRIVE SCREEN

LD27866

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды