York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 25 / 160

JOHNSON CONTROLS

SECTION 2 – OPTIVIEW CONTROL CENTER

FORM 160.79-O3

ISSUE DATE: 11/09/2018

OPTIVIEW CONTROL CENTER IN DETAIL

The OptiView™ Control Center display is highlighted

by a full screen graphics display. This display is nested

within a standard keypad, and is surrounded by “soft”

keys which are redefined based on the currently dis-

played screen. Eight buttons are available on the right

side of the panel, and are primarily used for navigation

between the system screens. At the base of the display

are 5 additional buttons. The area to the right of the

keypad is used for data entry with a standard numeric

keypad provided for entry of system setpoints and lim-

its.

The

Decimal

key provides accurate entry of

setpoint values.

A +/- key has also been provided to allow entry

of negative values and AM/PM selection dur-

ing time entry.

In order to accept changes made to the chiller

setpoints, the Check key is provided as a uni-

versal ‘Enter’ key or ‘Accept’’ symbol.

In order to reject entry of a setpoint or dismiss

an entry form, the

‘X’

key is provided as a uni-

versal ‘Cancel’ symbol.

Cursor

Arrow

keys are pro-

vided to allow movement on

screens which contain a large

amount of entry data. In ad-

dition, these keys can be used

to scroll through history and

event logs.

The Start/Stop control is operated via a three-position

rocker switch. When toggled all the way to the right, it

is considered in the

STOP/RESET

position. When in

the middle position, this is considered the RUN state.

When toggled to the left-most position, it is considered

in the START state. Each state is described in detail

below:

• STOP / RESET (O)

When in this position, the chiller will not run un-

der any condition. The switch must be placed in

this state following a Safety shutdown before the

chiller is allowed to restart. This guarantees that

manual intervention has taken place and the shut-

down has been acknowledged.

• START (



)

The switch can only remain in this position when

being acted upon by a manual force. Once the user

has released the switch, it automatically reverts to

the RUN position. Generally, this state only oc-

curs momentarily as the operator attempts to lo-

cally start the unit. Once this position has been

sensed, if all fault conditions are cleared, the unit

will enter the system prelube (start sequence).

• RUN (



)

When in this position, the chiller is able to oper-

ate. The switch spring-returns to this state after it

has been toggled to the

START

position. When

in this state, the chiller is allowed to function nor-

mally, and will also allow the chiller to automati-

cally restart following a Cycling shutdown. The

switch must be in this state to receive a valid re-

mote start signal when operating under a remote

control source.

LD08639

FIGURE 3 -

OPTIVIEW™ CONTROL CENTER

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды