York OPTIVIEW YD Series Скачать руководство пользователя страница 90

Страница: 90 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

Voltage Total Harmonic Distortion (L1, L2, L3)

Displays the 3-phase voltage Total Harmonic Distor-

tion (THD) measurements.

RMS Filter Current (L1, L2, L3)

Displays the 3-phase filter current values as measured

by the Harmonic Filter.

Supply Current Total Demand Distortion (L1,

L2, L3)

Displays the 3-phase Current Total Demand Distortion

(TDD) measurements.

RMS Supply Current (L1, L2, L3)

Displays the 3-phase RMS currents for each line.

Supply Contractor (LED)

Indicates whether the output to the supply contractor

is energized.

Precharge Contractor (LED)

Indicates whether the output to the precharge contrac-

tor is energized.

PROGRAMMABLE

None.

NAVIGATION
Home

Access Level Required: VIEW

Returns the user to the Home screen.

VSD

Access Level Required: VIEW

Returns the user to the VSD screen.

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Бренды по названию

Популярные бренды