York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 55 / 160

JOHNSON CONTROLS

SECTION 2 – OPTIVIEW CONTROL CENTER

FORM 160.79-O3

ISSUE DATE: 11/09/2018

This screen allows calibration of the compressor

Variable Geometry Diffuser position potentiometer.

Requires a login access level of

SERVICE.

DISPLAY ONLY
VGD Opening (LED)

Illuminates when an open signal is being applied to the

VGD.

VGD Closing (LED)

Illuminates when a close signal is being applied to the

VGD.

VGD Feedback Voltage

Displays the VGD position potentiometer feedback

voltage.

Calibration In Progress (LED)

Illuminates when a calibration sequence is in progress.

Calibration Messages

These are text messages which step the user through

the calibration process and indicate its success or

failure.

PROGRAMMABLE
Start Calibration

Initiates the calibration start.

Cancel Calibration

This button is displayed during the VGD calibration

process. It allows the user to cancels a calibration se-

quence that is in progress.

NAVIGATION
Home

Access Level Required: SERVICE

Causes an instant return to the Home Screen.

VGD 1 or 2

Access Level Required: SERVICE

Moves to the VGD 1 subscreen that allows viewing of

the associated VGD parameters.

VARIABLE GEOMETRY DIFFUSER (VGD) CALIBRATION SCREEN

FIGURE 15 -

VARIABLE GEOMETRY DIFFUSER 1 CALIBRATION SCREEN

LD27854

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды