background image

JOHNSON CONTROLS

38

FORM 160.79-O3 

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen displays a cutaway view of the chiller 

condenser. Animation indicates condenser liquid flow. 

This screen also serves as a gateway to controlling the 

Refrigerant Level.

DISPLAY ONLY
Entering Condenser Liquid Temperature 

Displays the water temperature as it enters the 

condenser.

Leaving Condenser Liquid Temperature 

Displays the water temperature as it leaves the condenser.

Condenser Saturation Temperature 

Displays the saturation temperature in the condenser.

Condenser Small Temperature Difference

Displays the difference between the Condenser Refrig-

erant temperature and the Leaving Condenser Liquid 

temperature. The Condenser Refrigerant temperature 

will be represented by the Condenser Saturation tem-

perature.

Condenser Pressure 

Displays the refrigerant pressure in the condenser.

Drop Leg Refrigerant Temperature 

Displays the temperature of the refrigerant in the drop 

leg between the condenser and evaporator shells, if the 

sensor is present and "Enabled".

Sub-Cooling Temperature

Displays the difference between the Condenser Refrig-

erant temperature and the Drop Leg Refrigerant tem-

perature. The Condenser Refrigerant temperature will 

be represented by the Condenser Saturation tempera-

ture. If the Drop Leg sensor is not present, this tem-

perature is not displayed.

Condenser Liquid Flow Switch (Open / 

Closed)

Indicates whether flow is present in the condenser.

Condenser Liquid Pump (Run / Stop)

Indicates whether Condenser liquid pump is operating.

Condenser Refrigerant Level

Displays the present position of the refrigerant level.

Active Level Setpoint 

Displays the setpoint to which the refrigerant level is 

being controlled. 

CONDENSER SCREEN

LD27846

FIGURE 7 - 

CONDENSER SCREEN

Содержание OPTIVIEW YD Series

































































































































































Отзывы: