York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 70 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen allows the user to specify the chiller load

conditions under which the lag compressor is cycled on

and off. Both compressors are not started at the same

time. The lead compressor is started first. If it does not

meet the load requirements as established with the fol-

lowing setpoints, the lag compressor is started. After

the lag compressor is running, it will be shutdown if the

load decreases to the point established by the following

setpoints. Parameters pertinent to chiller loading are

displayed. Also, compressor #1 or #2 can be selected

for lockout.

DISPLAY ONLY
Temperature Differential (Leaving Chilled Liq-

uid Temperature - Setpoint)

Displays the difference between the Leaving Chilled

Liquid Temperature and the Leaving Chilled Liquid

Temperature Setpoint.

Delta T Rate

Displays the rate of change of the Leaving Chilled Liq-

uid Temperature as “X.X ºF/Minute”. Value displayed

represents a five-point rolling average obtained as fol-

lows: After the first 3 minutes of chiller run time, the

Leaving Chilled Liquid Temperature is sampled once

every minute. The previous reading is subtracted from

the present reading and the last 5 results are averaged

to obtain a five-point rolling average. Displayed as

zero when chiller is not running.

Lead % Full Load Amps

Displays the motor current of the lead compressor as

a percentage of the full load amps of that compressor

motor.

Lead PRV Position

Displays the position of the lead compressor pre-rota-

tion vanes position.

Lead VGD Position

Displays the position of the lead compressor Variable

Geometry Diffuser.

Lead VSD Output Frequency

Displays the value of the lead compressor VSD output

frequency if a VSD is installed.

Lag % Full Load Amps

Displays the motor current of the lag compressor as

a percentage of the full load amps of that compressor

motor.

CAPACITY COMPRESSOR CYCLING SCREEN

FIGURE 23 -

CAPACITY COMPRESSOR CYCLING SCREEN

LD27862

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды