York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 69 / 160

JOHNSON CONTROLS

SECTION 2 – OPTIVIEW CONTROL CENTER

FORM 160.79-O3

ISSUE DATE: 11/09/2018

This screen displays the Anti-Surge Tuning param-

eters. A Service Level password is required to access

this screen.

DISPLAY ONLY

All other parameters are view only and may be request-

ed by Product Technical Support or Chiller Engineer-

ing when assisting in troubleshooting.

PROGRAMMABLE

There are no Programmable setpoints on this screen.

The technician may be asked to provide a picture of

this screen by Product Technical Support or Chiller En-

gineering when assisting in troubleshooting.

LCHLT Setpoint Ramp Rate

When the chiller is not running, the Active Setpoint

is set to Entering Chilled Liquid Temperature minus

a programmable offset (default 5°F), but not adjusted.

LCHLT Setpoint Start Offset

The LCHLT setpoint offset above the Active setpoint.

(Adjustable 0.0°F to 10.0°F, Default 5.0°F)

Lead PRV Start Position

The desired start position of the Lead compressor PRV.

(Adjustable 0% to 100%, Default 0%)

Gear Ratio Override

Allows the technician to add a buffer above the operat-

ing surge plane by adjusting this parameter. (Adjust-

able 0.0000 to 7.0000, Default 0.0000)

NAVIGATION
Home

Navigates to the Home screen.

Capacity Control

Returns to the Capacity Control screen.

Anti-Surge Tuning

Navigates to the Anti-Surge Tuning screen

ANTI-SURGE TUNING SCREEN

FIGURE 22 -

ANTI-SURGE TUNING SCREEN

LD27861

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды