York OPTIVIEW YD Series Скачать руководство пользователя страница 34

Страница: 34 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

Evaporator Pressure

Displays the present refrigerant pressure in the evapo-

rator.

Evaporator Saturation Temperature

Displays the present saturation temperature in the

evaporator.

Condenser Liquid Temperature - Leaving

Displays the temperature of the liquid as it leaves the

condenser.

Condenser Liquid Temperature - Entering

Displays the temperature of the liquid as it enters the

condenser.

Condenser Pressure

Displays the refrigerant pressure in the condenser.

Condenser Saturation Temperature

Displays the saturation temperature in the condenser.

Oil Sump Temperature

Displays the temperature of the oil in the sump.

Chiller Current Limit Setpoint

Displays the Chiller Current Limit Setpoint. The Chill-

er Current Limit Setpoint could be from a 0-20 mA,

4-20 mA, 0-10 VDC or 2-10 VDC input in Analog re-

mote mode or PWM input in Digital remote mode or

SC-EQ communication interface in ISN (BAS) remote

mode or a Local Chiller Limit Setpoint entered at the

Keypad.
This setpoint is in effect after the Lead Compressor

Pulldown Time setpoint has elapsed and for the re-

mainder of system run.

PROGRAMMABLE

None

NAVIGATION
Home

Access Level Required:

VIEW

Causes an instant return to the Home Screen.

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Бренды по названию

Популярные бренды